Misbehaving spider

[Rappy Freak]

This is the quad I have been asking on chat about help with and here is the video as asked for.

Spider jumping about on Vimeo


The escs are Hobbywing 12A, the motors are E flight cf2822 and lipo is 3S 3000mah.  Flight controller is a KK2

Any ideas would be great and before anyone says it it has been turn on and off 

[Gaza07]

It looks like it could be wired wrong as the motor seems to respond the wrong way, double check all connections are right 

[icedfusion]

THat looks like a KK2 board.

Double check to make sure, as GAza says, that the motors are going in the right direction. This is easy to check as there is a menu option which will show you what direction each motor is supposed to go in. Also, I assume you set the frame configuration to X mode as the KK2 comes as + by default.

Once you have verified your motors, then I have to say that I get some vibration issues with this FC on a frame - I will post a vid to show what I mean, however, I can still get air bourne!

Cheers

ice.

[micarus]

It looks like it could be wired wrong as the motor seems to respond the wrong way, double check all connections are right 

Its not wired wrong M8 as it has flown <briefly> and all connections are good ,  no bullet connectors and has been completely rewired with these motors CF2822 and 12amp hobbywing "flyfun" E.S.Cs. props all ballanced and  all motors following stick inputs ?  but gyros don't seem to be correcting it properly , the board was checked out on two other multi's that flew fine.
                       Cheers  MIKE.

[Gaza07]

When you test it are you testing it with auto level on or off, I saw the video of Balders testing your board and to be honest it looked like the gyro wasn't working for him at first, I cant see how its motors or esc's because as long as they start ok and at the same time they seem fine, its difficult really to know how to fix it when you cannot see it in front of you, I have a gut feeling you have a gyro problem on the board and that Balders flying skills are so good it didnt show so much, I would be more than willing to take a look at your board but you would have to post it to me, its up to you.

[Balders]

those issue I had when I first tested were because i had two motors wired to the wrong plugs :)

Soon as I corrected that it was perfect. Thumbs off stuff, not in level mode.

[micarus]

When you test it are you testing it with auto level on or off, I saw the video of Balders testing your board and to be honest it looked like the gyro wasn';t working for him at first, I cant see how its motors or esc';s because as long as they start ok and at the same time they seem fine, its difficult really to know how to fix it when you cannot see it in front of you, I have a gut feeling you have a gyro problem on the board and that Balders flying skills are so good it didnt show so much, I would be more than willing to take a look at your board but you would have to post it to me, its up to you.

Thanks for the offer Gaza but Balders checked it and found the board good! Rappy and I have had it flying <breafly> but it is a real handfull , I have ballanced Graupner 10x5s on it now and have tried different foam under the reciever and f.c board to no avail and just about had it   in fact I have another KK2 on it now and it';s just as crap.
Ordered a Turnigy Talon now to try the boards on.

        Cheers  to all,   MIKE.

                           

[Gaza07]

No worries mike I hope the new frame does the job 

[Balders]

I';m convinced that problem is down to your esc';s

Frustrated at not being able to help from afar...

[micarus]

I';m convinced that problem is down to your esc';s

Frustrated at not being able to help from afar...

Hi Steve , Just seen your post DOH! anyway think you are most likely correct but am curently trying to flash the two boards to V1.2 which I hope will help but will let you <and everyone else> know when and if I sort it out.

             Cheers  M8                          MIKE .   :uk: