What best paramet set, BlHeli Firmware

[Nautilus]

I have starte Flash my Turnigy Plus 30A ESC With BlHeli Firmware

Shut I use the standart Parameter or is there better setup

It shut work with 4S on Hex frame

:huh

[teslahed]

I can probably give you a little bit of advice, but it would help if I knew what motors you are using.

I use these settings on most of my motors;



I use 1064 - 2000 throttle range as well sometimes because that';s the same as simonk defaults to in the multiwii code.

[Nautilus]

I can probably give you a little bit of advice, but it would help if I knew what motors you are using.

I use these settings on most of my motors;



I use 1064 - 2000 throttle range as well sometimes because that';s the same as simonk defaults to in the multiwii code.

my motor is HP4215 460KV 24N18P Multicopter Brushless Motor

I know it show only work ( tested with 5 and 6 cell Lipo )

motor info on RCtimer side
"Configuration  24N18P, KV- 460KV, The no load current:0.75 Amp, Battery: 2-6S"


http://www.rctimer.com/index.php?gOo=goods_details.dwt&goodsid=848&productname=

both if check HP4215 630KV 24N18P Multicopter Brushless Motor

that tested with 3S Lipo

http://www.rctimer.com/index.php?gOo=goods_details.dwt&goodsid=848&productname=

[teslahed]

As it';s a lower kv motor you may need to alter the motor timings. I am not sure because i haven';t used motors like that myself.

[Nautilus]

As it';s a lower kv motor you may need to alter the motor timings. I am not sure because i haven';t used motors like that myself.

Ok i have to try the standart parameter, and see if possible to make a plug to set parameter later

[shazzy]

Sorry to take over, but would the settings change (from the image you uploaded) if the Turnigy plush 30A escs were connected to DT700 motors?

Noob here so I dont really understand the parameters but I know the the default BLHeli settings arent quite write for my quad. If there are different how so? And any direction to where I could find them?

[teslahed]

You could alter the throttle limits - i think it defaults to 1200 to 1800 - i changed mine to 1000 to 2000 - the full range my transmitter gives out.

Other than that i am not sure what the best settings would be for your setup.

[TheEdge]

I am thinking of flashing my esc';s to get a more stable quad, but I have no idea of what parameters to use.

FY450 Flame wheel frame
Crius AIO Pro 2 Flight controller
Sunnysky 2212 980kv
Skywalker 20A 2A-BEC Brushless ESC
10x4,7 propellers
3S lipos.

Turnigy 9x transmitter.

Main use will be aerial photo/fpv not really acrobatic flying style.

As far as I can see, the skywalkers cannot use simonk, but need to use the BlHeli. So, what parameters should I use for BlHeli for my ESC';s?

Or should I just get some other esc';s already flashed with SimonK? (in this case, any recommendations?)
Would getting  these be an alternative?

With this setup I get 21 minutes of flight on a 5000mah 3s lipo with a small action cam mounted.
If I get other esc, will getting esc with higher current rating affect my flight time?

I have bought this programmer for flashing my turnigy 9x with other firmware, can this programmer also be used for the esc';s?

[nub]

just flash them with the multi version of the BLheli code for that ESC, i never had to change any settings when flashing my DJI 30A ESC';s and my quad flies fine, changing your ESC';s shouldn';t affect anything, i have no idea about the programmer.