User Info

 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

MultiRotorUK ShoutBox

Refresh History
  • hoverfly: beararsedcheek... :laugh:
    September 18, 2018, 18:42:15
  • Bad Raven: or bearreft, or bear left?
    September 17, 2018, 14:21:16
  • Bad Raven: or isnotherebear
    September 17, 2018, 14:20:30
  • Bad Raven: more like doesnotcarebear
    September 17, 2018, 14:20:07
  • Gav: carebear?
    September 17, 2018, 11:37:44
  • atomiclama: you there bear??
    September 15, 2018, 11:42:45
  • Reman: Got stuck in traffic yesterday. After an hour I started using my phone (And an OTG cable) to look through the media files on a keyring of my old USB sticks. Found one that had the entire run of "Firefly" on it. I got through 3 episodes before the traffic started moving again....... God, That really was an amazing show.
    September 14, 2018, 19:52:46
  • Gav: ok dude
    September 08, 2018, 16:40:59
  • mo_miah: Gav- if its a camera ship then TBS crossfire is definitely what you need, the FrSky has limited channels and telemetry options, TBS crossfire has much better features and more channels to control camera gimbals etc
    September 07, 2018, 11:53:01
  • Gav: mo miah - wanna swap from immertionRC UHF and try something else on my camera Ship.
    September 07, 2018, 11:25:40
  • DarkButterfly: My laminate arrived, the rebuild is coming along ~~
    September 06, 2018, 20:00:44
  • hoverfly: I coated a couple of Slipstreams  a few years ago  It stiffened up the wing nicely .On the down side although it prevented dings when i had an high speed"arrival" it left the resin cracked. and the glass lifted slightly.  Well stuck laminate stiffens the wing and is flexible..
    September 06, 2018, 18:26:13
  • DarkButterfly: I'm doing laminate, just put my order in for some, also got some balsa wood for the side parts, had to use a kitchen knife to seperate the foam from the busted wood
    September 05, 2018, 13:21:11
  • atomiclama: Thanks, can't decide on fibre glass or laminate. Like the idea of fibre for some reason, don't know why.
    September 05, 2018, 10:45:48
  • Bad Raven: Usng PolyC, yes
    September 05, 2018, 10:13:54
  • atomiclama: Anyone fibre glass coat their wings??
    September 05, 2018, 09:30:22
  • atomiclama: @DB well you obviously need a bigger motor and ESC, as flying slower is just not possible.  ::)
    September 05, 2018, 09:29:59
  • DarkButterfly: ~~
    September 05, 2018, 09:10:18
  • hoverfly: If you put a couple of coats of Eze Kote on the wing before the laminate it sticks really well ..no lifting.. :smiley:
    September 05, 2018, 08:47:37
  • DarkButterfly: If it makes you feel better, I’m going to completely refurbish my falcon Evo with new balsa sides and new laminate ~~
    September 04, 2018, 21:42:53

Who's Online

Theme Selection



Forum Default

Permanently

Author Topic: Inav problems  (Read 396 times)

Offline hoverfly

  • Trade Count: (0)
  • Hero Member
  • *****
  • Posts: 2769
  • Liked: 1182
  • Country: gb
  • Quads, lots of quads
Inav problems
« on: March 14, 2018, 13:18:38 »
@ Wyntrblue.
board is
Matek F405-CTR AIO Flight Controller,  with  inav_1.9.0_MATEKF405-RC1.hex this one was advised by Hobbyrc after i was unable to load the ones on the Inav  config.

The second one that loads but is not suitable is..inav_1.8.0_MATEKF405.hex This one is recommend by Matek.
I had another look this morning but the deeper i look i suspect a bug. :cry

Reptile folder , alien 500 , F/ Shark Attitudes,
 .Tarot 650, Air-rio Kinetic.. DX9  Various wings and planks.. Taranis x9D+..Mavic..Armattan.. Chameleion...
Massive over draught.....

Offline Wyntrblue

  • Site Sponsor
  • Trade Count: (0)
  • Sr. Member
  • *****
  • Posts: 274
  • Liked: 64
  • Country: gb
Re: Inav problems
« Reply #1 on: March 14, 2018, 13:58:42 »
do you get the same issue when you flash an non release candidate version?

https://github.com/iNavFlight/inav/releases/download/1.9.0/inav_1.9.0_MATEKF405.hex

Offline hoverfly

  • Trade Count: (0)
  • Hero Member
  • *****
  • Posts: 2769
  • Liked: 1182
  • Country: gb
  • Quads, lots of quads
Re: Inav problems
« Reply #2 on: March 14, 2018, 17:04:02 »
That was the one that Hobbyrc recommended. it had the least problems.Everything looking good but not arming.
Motor test was ok , only indication of problem apart from not arming was when i set the failsafe to a switch it worked in the mode tab but is i navigated away it turned off again,  in the instructions it states that if there is a conflict with a setting it will cancel it., for example using same port for two functions.. the more i look at it i suspect a bug. all the previous boards have worked well. :shrug:

Edit when i loaded the second firmware when i tried to calibrate it only did level the six position  calibration window didn't  appear.
« Last Edit: March 14, 2018, 17:07:32 by hoverfly »
Reptile folder , alien 500 , F/ Shark Attitudes,
 .Tarot 650, Air-rio Kinetic.. DX9  Various wings and planks.. Taranis x9D+..Mavic..Armattan.. Chameleion...
Massive over draught.....