Welcome to Multi-Rotor UK. Please login or sign up.

Saturday,July 11, 2020, 16:02:11

Login with username, password and session length

Shoutbox

sh0wtime:
08 Jul 2020 23:54:24
howdy
hoverfly:
08 Jul 2020 10:22:40
My mother did it, which explains the mental conditions of my sisters, its a genetic  thing. :D
Andy7:
07 Jul 2020 14:01:29
... I could ask how you knoiw this... but I would regret it.
hoverfly:
07 Jul 2020 11:53:34
Little known fact, if you push a runner bean seed up your nose the moisture will cause it to germinate, and expand.You wont get any beans though just  two black eyes. :o
Andy7:
04 Jul 2020 13:16:48
VIDEO or it didn't happen!! :) Nice going though, keep it up!
Bad Raven:
02 Jul 2020 19:46:48
 ~~
whoelseisbored (LiamHowe89):
02 Jul 2020 17:45:19
Sounds basic but I'm happy with it  :laugh:
whoelseisbored (LiamHowe89):
02 Jul 2020 17:45:05
Managed a split s :D
badger1:
28 Jun 2020 12:29:49
BF GPS Rescue mode configured - what could possibly go wrong?   :o
badger1:
27 Jun 2020 21:07:37
and can't make it back to where you take off from   :laugh:
Members
Stats
  • Total Posts: 199017
  • Total Topics: 20055
  • Online Today: 12
  • Online Ever: 530
  • (Tuesday,June 26, 2012, 08:34:46 )
Users Online
Users: 2
Guests: 16
Total: 18

Theme Changer





thumbnail

3d - Printworx

Printing 3d Forum

New Frame design

Started by robhho123, Thursday,September 03, 2015, 12:39:59

Previous topic - Next topic

robhho123

Hi Guys

I';ve designed a new frame for the hubsan x4 internals + spectrum micro fpv camera

this frame has 85mm centres and locates the flight controller in dead centre position between the motors.I have designed it in a way that the fpv camera locates securely so there will be no movement and it will take a 750mah battery that is raised up above the FC on posts and fixing points to use a loom band to secure the battery. I need to do some modification to the frame drawing but I will put the file for upload so people can print it out themselves if they want.

What do people think good/bad?








Rob

Hurricane 250 & loads of other micro's the I bodge together for some fun.

JeremyE

Looks good. What FPV setup are you using?

nub

looks good to me but know what you do need to print, one of these or something similar http://www.thingiverse.com/thing:645287 :smiley:
Point and click.

Monkey see, Monkey do.

add1ct3dd

Sorry to say it, but those arms will snap in the first crash!

Nice idea though.
ZMR250 x 2, Quanum 250, Kermit 170mm.

kilby

Looks really nice but the arms may be a little fragile.

You may be able to leave a channel to run a thin CF rod through to beef it up a bit.
Not much kit, but what I have I like
Armattan Tilt 2, Morphite 180, Quark 150, Decapitated NanoQX
Taranis+

robhho123

The aerial sits lower than the props so it';s ok if landed upside down on something flat.ha

You guys must be psychic because one of them has just done that I made the stupid mistake of letting a a friend at work fly it bare in mind he';s never flown one he flew it round erratically then went up 20ft in the air and then slammed it straight into the ground.

I didn';t even get a sorry.

i';ve got another frame printing at the mo and I may try cast some out of polyurethane to give it abit of flex and strength.

 
Rob

Hurricane 250 & loads of other micro's the I bodge together for some fun.