OpenPilot Version 15.02 (Ragin’ Cajun) now released.

[manc]

https://www.openpilot.org/new-release-15-02-ragin-cajun/

Release Notes – OpenPilot – Version RELEASE-15.02
** Bug
* [OP-969] – Input Configuration Wizard has scrollbars showing up and next/previous buttons are pushed down out of sight
* [OP-1034] – CCPM Config Widget crashes GCS if required boxes aren't set i.e. Channel set to None
* [OP-1236] – Icons on Welcome tab – moves to the left
* [OP-1466] – Gcs crashes on Helicopter config tab
* [OP-1522] – Improve Robustness of OPLink radio
* [OP-1601] – Still not enough ram on CC for gps to be usable
* [OP-1644] – Radio Setup Wiz problem with 6 flight modes
* [OP-1670] – cruise control conflict with flight modes (rate & acro +)
* [OP-1680] – OPLink control limited to 1000-1896
* [OP-1682] – Overflow issue with pwm rx and CC3D
* [OP-1686] – Slave OPLM should receive PPM in PPM_only mode
* [OP-1706] – Output Reverse checkboxes tick them selves when min equals max
* [OP-1718] – FW vehicle setup wizard may strip servo gears
* [OP-1722] – libusb include is incorrect.
* [OP-1728] – FW servos ignore set neutral
* [OP-1733] – version-info.py should check for version-info.json not git repo.
* [OP-1735] – Build fails with a tilde (~) in path.
* [OP-1737] – Min/max will be greyed even if motor output test is canceled
* [OP-1741] – Repo path is incorrect in version_info.pro
* [OP-1743] – cc3d fails to connect once "next " is loaded 2-23-15
* [OP-1744] – Vehicle config wizard produces a bad configuration
* [OP-1754] – Vehicle Wizard bad config when setting PPM in and RapidESC out
* [OP-1755] – Add additional path for cloudconfigs
* [OP-1758] – Upgrade hidapi for all OSs (except windows) to solve mac issue:Fix incorrect device list after device removal
* [OP-1761] – Wizard bad config when PPM in, RapidESC out and hexa frame with CC/CC3D/Atom
* [OP-1764] – System should sanity check RC Input Channel value ranges and raise alarm accordingly
* [OP-1768] – PWM Sync and OneShot125 wizard output level and warning are incorrect
** Improvement
* [OP-1519] – Auto Reboot of board when required by Wizard
* [OP-1576] – Remove tx resent accounting from OPlink
* [OP-1635] – Remove Quad H from wizard to avoid confusion with Quad X
* [OP-1650] – Reduce telemetry to improve OPLink
* [OP-1658] – Sensor driver API and overhaul of sensor module
* [OP-1683] – Support synchronous (OneShot) and OneShot125 output mode
* [OP-1685] – Support OneShot/OneShot125 for CC* targets
* [OP-1694] – Make package make rule non-nested
* [OP-1698] – Add easy to set channel passtrough GCS functionality
* [OP-1704] – Add support for sanity check custom hooks
* [OP-1759] – Hide CC3D non-supported options (GPSAssist)
** Task
* [OP-1721] – C++ enable flight controller and upgrade ARM tools
* [OP-1738] – change default flight modes and thrust settings
* [OP-1747] – 15.02 rc1 motor end points do not reflect oneshot125 / pwmsync
** Sub task
* [OP-1748] – Chinese translation for 15.02
* [OP-1752] – Add Alarm sub status to SystemHealth
The full list of features, improvements and bugfixes in this release is accessible here:
https://progress.openpilot.org/issues/?filter=12161