Welcome to Multi-Rotor UK. Please login or sign up.

Tuesday,August 20, 2019, 21:45:11

Login with username, password and session length


19 Aug 2019 09:14:20
Good for you!  ~~
18 Aug 2019 19:13:57
Had another negative encounter, it's been a few years since the last one, just an uneducated ******, going on about drones being illegal yada yada yada.    :-/
Still that didn't spoil my flying time, had an absolute blast  ~~
07 Aug 2019 19:52:01
ooooh mrs jones  :D
30 Jul 2019 15:26:34
D.B. you tightwad.. :cool:
29 Jul 2019 20:14:10
DB that just means you have shed loads of props in the first place ;-)
29 Jul 2019 18:53:33
Just had a thought, even with all the crashing I've done, I haven't bought any replacement props in over a year ~~
09 Jul 2019 19:45:42
May the sun shine and winds be light for BFU#8. Son't forget lots of vids for those of us unable to attend.  :D
09 Jul 2019 18:10:30
Hope you all have a great day  :beer2:
09 Jul 2019 14:05:28
BFU#8 details locked in for this saturday - see the head of the forum thread for all details.
05 Jul 2019 21:51:05
Good for genital warts as well......or so I'm told.. :hmm
  • Total Members: 8066
  • Latest: badger1
  • Total Posts: 196558
  • Total Topics: 19801
  • Online Today: 50
  • Online Ever: 530
  • (Tuesday,June 26, 2012, 08:34:46 )
Users Online
Users: 1
Guests: 41
Total: 42

Theme Changer

3d - Printworx

Printing 3d Forum

Annoying beep, beep, beep

Started by Bergerac56, Friday,January 11, 2013, 22:58:33

Previous topic - Next topic



First of all congratulation for this forum. It was the place where I found the best information';s to make my first steps with MPNG.

I own 2 MR';s: a GAUI 500X and a DJI S800.   Both are "controlled" by a AIOP crius V1.1 + GPS loaded with multiwii. Reading through this forum I wanted to give a try to MPNG (2.7 R4 for the moment). It went like a charm for the DJI but not for the GAUI. On the GAUI, after eeprom erase, ESC calibration, etc I still face the very annoying beep, beep, beep. Impossible to go futher.

Same version of the firmware, same version of board and, obviously adaptation of HEX X to QUAD X

This is perhaps a very stupid question already answered tons of times,   :embarrassed but... what is the cause of those rapid and repetitive beeps?

Thanks a lot



The raoid beeps from the esc';s are telling you they are not calibrated and out of range, extend the end points on your throttle channel and try to re calibrate them 115% each end is a good place to start and go up from that if you need to  ~~


Thank you for your reply. I calibrated the ESC the same way that I did with multiwii. Everythig was going smooth and nicely with this firmware. I will follow your suggestion and redo the whole process.


Even if you think you did everything right, you have to doubble check...  :whistling: . My TX is a "Royal pro". The range of the trottle was "limited" by default. I did not pay attention to that.

Thanks again. Problem solved  :laugh:


I flashed my tgy plush18';s with bheli firmware and disabled those beeps, i can tell if they are working by watching the probs rotate ;)
Talon V2 quad X
crius AIO pro v1 (latest mpng)
cruis GPS v2, chinese elcheapo sonar, custom led works
4x plush 18 with BLheli 0.9
4x sk3 1130kv + 8x45
turnigy er9x with frsky telemitry enabled, backlight and lipo mods


Quote from: willumpie82 on Sunday,January 13, 2013, 14:10:12
I flashed my tgy plush18';s with bheli firmware and disabled those beeps, i can tell if they are working by watching the probs rotate ;)

Hi willumpei82,
I noticed that you have the Crius run on mpng with the BLheli firmware ESC.
I got the Crius V2 and the DJI 450 kit, just loaded Mpng on mine and flashed those DJI ESCs to the BLheli 10.
Could you please show me the Basic and Advanced setup page on your ESC so I can have some thing to start with.

DJI flame wheel 450 kit with motor and ESC
Crius AIO Pro V2 with Mpng 2.8R3
BLheli firmware on DJI ESC