Major MultiWii issues connecting to transmitter and more

[stickboy]

I thought I had got somewhere with this MultiWii but my problems seems to have grown. Main issue i';m trying to figure out is how to connect my Tx/Rx. I';m using a futaba so I edited the config.h a little but getting no where. Right now my WinGui shows nothing at all, and even though my receiver shows a green light, its as if the FC isn';t receiving or recognizing any signal at all.

Second issue is I can';t get a satellite lock. The little red led is solid all the time but blinking green/red In the GUI.

Third problem is the blue line in my sensor graph is all crazy. Posting some pics with this so let me know what you think.

Only other thing I can say is the blue led on the FC board blinks constantly. I';m running 2.3 on the MW Pro with MTK GPS.

Any help would be greatly appreciated! I';m determined to get this thing figured out one way or another.

[stickboy]

Here';s the code I edited. Everything else is an exact copy of this guy:       https://www.youtube.com/watch?v=9TIUif3PE9U




/*************************************************************************************************/
/*****************                                                                 ***************/
/****************  SECTION  3 - RC SYSTEM SETUP                                            *******/
/*****************                                                                 ***************/
/*************************************************************************************************/

  /* note: no need to uncomment something in this section if you use a standard receiver */

  /**************************************************************************************/
  /********                       special receiver types             ********************/
  /**************************************************************************************/

    /****************************    PPM Sum Reciver    ***********************************/
      /* The following lines apply only for specific receiver with only one PPM sum signal, on digital PIN 2
         Select the right line depending on your radio brand. Feel free to modify the order in your PPM order is different */
      //#define SERIAL_SUM_PPM         PITCH,YAW,THROTTLE,ROLL,AUX1,AUX2,AUX3,AUX4,8,9,10,11 //For Graupner/Spektrum
      #define SERIAL_SUM_PPM         ROLL,PITCH,THROTTLE,YAW,AUX1,AUX2,AUX3,AUX4,8,9,10,11 //For Robe/Hitec/Futaba
      //#define SERIAL_SUM_PPM         ROLL,PITCH,YAW,THROTTLE,AUX1,AUX2,AUX3,AUX4,8,9,10,11 //For Multiplex
      //#define SERIAL_SUM_PPM         PITCH,ROLL,THROTTLE,YAW,AUX1,AUX2,AUX3,AUX4,8,9,10,11 //For some Hitec/Sanwa/Others

      // Uncommenting following line allow to connect PPM_SUM receiver to standard THROTTLE PIN on MEGA boards (eg. A8 in CRIUS AIO)
      #define PPM_ON_THROTTLE

    /**********************    Spektrum Satellite Reciver    *******************************/
      /* The following lines apply only for Spektrum Satellite Receiver
         Spektrum Satellites are 3V devices.  DO NOT connect to 5V!
         For MEGA boards, attach sat grey wire to RX1, pin 19. Sat black wire to ground. Sat orange wire to Mega board';s 3.3V (or any other 3V to 3.3V source).
         For PROMINI, attach sat grey to RX0.  Attach sat black to ground. */
      //#define SPEKTRUM 1024
      //#define SPEKTRUM 2048
      //#define SPEK_SERIAL_PORT 1    // Forced to 0 on Pro Mini and single serial boards; Set to your choice of 0, 1, or 2 on any Mega based board (defaults to 1 on Mega).
      //**************************
      // Defines that allow a "Bind" of a Spektrum or Compatible Remote Receiver (aka Satellite) via Configuration GUI.
      //   Bind mode will be same as declared above, if your TX is capable.
      //   Ground, Power, and Signal must come from three adjacent pins.
      //   By default, these are Ground=4, Power=5, Signal=6.  These pins are in a row on most MultiWii shield boards. Pins can be overriden below. 
      //   Normally use 3.3V regulator is needed on the power pin!!  If your satellite hangs during bind (blinks, but won';t complete bind with a solid light), go direct 5V on all pins.
      //**************************
      //   For Pro Mini, the connector for the Satellite that resides on the FTDI can be unplugged and moved to these three adjacent pins.
      //#define SPEK_BIND             //Un-Comment for Spektrum Satellie Bind Support.  Code is ~420 bytes smaller without it.
      //#define SPEK_BIND_GROUND 4
      //#define SPEK_BIND_POWER  5
      //#define SPEK_BIND_DATA   6

    /*******************************    SBUS RECIVER    ************************************/
      /* The following line apply only for Futaba S-Bus Receiver on MEGA boards at RX1 only (Serial 1) or PROMICRO boards.
         You have to invert the S-Bus-Serial Signal e.g. with a Hex-Inverter like IC SN74 LS 04 */
      //#define SBUS
      #define SBUS_SERIAL_PORT 1
      #define SBUS_MID_OFFSET 988 //SBUS Mid-Point at 1500

[dirtyharry]

Does your receiver output a sum ppm signal? I thought futaba was sbus .

AS a test I would re-comment your sum ppm and just run a single channel like the throttle.

Can';t help with your other woes

[stickboy]

Not sure about the s-bus, it has a port labeled for it but I';ve always just hooked mine up like a traditional receiver. Think I';m getting closer though. I commented out the "PPM sum receiver" part and re-flashed and noticed my throttle was actually moving in the winGUI when I hit the sticks. Turns out I made the newb mistake of hooking up my wires wrong! Haven';t managed to get it to arm yet but after I';ve a couple more things to try after checking a couple other threads.