Welcome to Multi-Rotor UK. Please login or sign up.

Friday,May 29, 2020, 13:34:06

Login with username, password and session length

Shoutbox

LiamHowe89:
29 May 2020 11:00:54
Banggood fairy for me... tonne of new standoffs  :laugh:
badger1:
27 May 2020 12:12:26
the HobbyKing fairy has been bearing LiPo's   :D
Gaza07:
27 May 2020 01:13:50
You have to say 6 like Eugene off the Preacher   :D
LiamHowe89:
26 May 2020 17:34:23
I see  :hmm:
Bad Raven:
26 May 2020 13:56:11
You have to say "six" with the right accent..........
Andy7:
25 May 2020 23:14:08
We have very high standards here you know.  :cool:
ched:
25 May 2020 19:49:45
:welcome: Liam
LiamHowe89:
25 May 2020 19:05:32
Yes... I'm daft. I can now spell 6. :laugh:
LiamHowe89:
25 May 2020 18:24:33
Guys, new here but am I being daft? I can't post a new post because apparently I don't know how many props a hexcopter has... got to be 6 right? Cheers!
ched:
25 May 2020 13:21:10
Not seen one AtomicLama. Sounds interesting
Members
Stats
  • Total Posts: 198468
  • Total Topics: 20014
  • Online Today: 28
  • Online Ever: 530
  • (Tuesday,June 26, 2012, 08:34:46 )
Users Online
Users: 3
Guests: 17
Total: 20

Theme Changer





thumbnail

3d - Printworx

Printing 3d Forum

CN-06 gps with crius v1.1

Started by paulcobra, Wednesday,January 09, 2013, 17:58:46

Previous topic - Next topic

paulcobra

Do i have to upload/change any settings on the cn-06 itself? If so can i do through the usb socket at the sametime i load the multi wii software to the crius?

secretman

in multiwii set gps serial 2 serial 2 speed 57600 or 112500 gps ublox done nothing to change in the gps

secretman

and yes after all set and load... you need to double power up.... plug power wait 10 sec... un plug and plug in for gps to activate it';s a bog on cn-06 gps...

bunnygirl80

Hi Paul,

When I did my CN-06 I had to remove the MultiWii and NAV board out of the equation and connect the GPS directly to the FTDI adaptor. You do have to update as the standard GPS module communicates at 9600 baud and you need to change it to 11500 for it to be compatible with the NAV/MultiWii. All the programming is done via the u-box u-center software which you can download from the u-blox website. http://www.u-blox.com/en/evaluation-tools-a-software/u-center/u-center.html Download version 7.02. I had to make a cable so that the four wires from the GPS went to four of the six connections on your FTDI board with the TX and RX crossed over. All sounds complicated, but it works and I now have a GPS signal and lock. 1) download u-Center 2) make the cable 3) connect and upload the code.

Hope this helps,

Stef
Always smile because you never know who could be falling in love with it. :) Drone Operator in North Wales. www.aerialworx.co.uk

Gaza07

Im taking it this is the crius AIOP v1.1 if it is then you don';t need the nav board and you don';t need to flash the gps at all as the multi wii code and the megapirate code send setup instructions to the gps through the serial port, you only have to flash the gps for lower spec flight controllers where there are no com ports and the gps has to connect via the i2c bus, version 2.1 of multi wii has to have a patch applied for this to work properly, there is a pre setup /patched version of multi wii 2.1 available for download from the forum in the crius AIOP section  ~~