User Info

 
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

MultiRotorUK ShoutBox

Refresh History
  • hoverfly: As I remember it was famous/notorious for its chicken poop welds.. :laugh:
    February 24, 2018, 21:05:05
  • Bad Raven: Honda had this belkief if they stripped all non-essentials off thay could compete against the 2 Strokes..... some chance!!  It was a commuter bike for the 4 miles each way I did four times a day.
    February 24, 2018, 18:10:37
  • Bad Raven: Try again... [link]
    February 24, 2018, 18:07:48
  • Bad Raven: [link]
    February 24, 2018, 18:02:35
  • Gav: got a pic?
    February 24, 2018, 17:47:40
  • Bad Raven: I have a 76 Honda CJ250T, 18k miles, it was a stripped down model without electric start, 2 into 1 exhaust, all weight saving.
    February 22, 2018, 17:29:21
  • hoverfly: My nephew picked up a 250 fleet star in super condition for £800.. He loves riding it around the Fens as the only hills are moles...
    February 22, 2018, 16:27:42
  • hoverfly: Sadly no, but when I go into.  fantasy  mode I trawl the net for a restoration  project..
    February 22, 2018, 16:11:12
  • Gav: you got a bike now hover?
    February 22, 2018, 14:57:59
  • hoverfly: That's a long weeee Slayer,   cystitis,???
    February 21, 2018, 20:34:31
  • Slayer23: feeling better now lol
    February 21, 2018, 19:03:35
  • Slayer23: Weeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
    February 21, 2018, 19:03:28
  • hoverfly: cz 250 twin.
    February 21, 2018, 13:09:44
  • Gav: what bike was it
    February 21, 2018, 11:49:36
  • hoverfly: I had similar a few years back , came home from work went int kitchen and made a cuppa  sat on a stool looking out the kitchen window.  There was a large space ,something was wrong, some scumbag a/hole had stolen my motorbike.. :banghead: :banghead: :banghead:
    February 21, 2018, 09:24:58
  • Reman: I just half woke up, opened my eyes to check the time. and while doing this I subconsciously noticed something wrong with the shape of shadows on the other side of the room. That woke me up with a jolt!!!  It seems I've got so used to seeing my camera hex perched up on the set of draws in the corner of my bedroom that the area now looks strangely empty without it (I took it apart on Sunday to begin the rebuild into its new Y6 frame)...... And now I'm wide awake at bloody half one in the morning....... And feeling like a paranoid pillock. :(
    February 21, 2018, 01:27:14
  • atomiclama: Cheers, already have bog standard rucsacs, looking for something with a bit easier access to the internals
    February 15, 2018, 13:12:41
  • CornishMule: Atomiclama, I also had the CS300 but recently got [link] It's big enough to put the Taranis X9D case inside, fatshark case, Lipo bag, a couple of tool bags, launch pad, monitor, laptop and copious props. 2 quads strapped to the front.
    February 15, 2018, 11:29:36
  • atomiclama: Cheers Hozza
    February 14, 2018, 09:00:06
  • yama: hooked on 90mm brushless drones now:)
    February 11, 2018, 15:45:24

Who's Online

Theme Selection



Forum Default

Permanently

Author Topic: A2212 brushless motor power wire replacement.  (Read 249 times)

Offline Dippi

  • Trade Count: (0)
  • Sr. Member
  • ****
  • Posts: 302
  • Liked: 14
  • Country: fi
  • S500 - Naza M Lite - Next build using 3510 360kv
A2212 brushless motor power wire replacement.
« on: August 10, 2017, 21:04:11 »
Is it possible to replace the power wires on these motors?
If yes how?

Offline ched999uk

  • Trade Count: (0)
  • Hero Member
  • *****
  • Posts: 2196
  • Liked: 513
  • Country: gb
Re: A2212 brushless motor power wire replacement.
« Reply #1 on: August 10, 2017, 21:24:40 »
It is possible depending on where it has broken. Normally multi strand wire is soldered to the enamel coated windings on the motor. To solder to the windings you need to remove some enamel by scraping or sanding the coating off. You might have to dismantle the motor to get at the stator.
Be aware that the internal wiring of a motor may not just be 3 wires, there may be enamelled wires linked together before the flexible wires are soldered on.

Hope that gives you some clue.